|
1) 지식 창고는 본인이 작성한 콘텐츠(팁/노하우/리소스/강좌 등)을 무료 혹은 가상화폐인 납포인트를 통해 공유하는 공간입니다.
2) 본인이 작성한 콘텐츠에 대해서만 지식 창고에 등록할 수 있으며, 저작권에 위배되는 콘텐츠는 사전경고 없이 삭제될 수 있습니다.
3) 콘텐츠 구매 및 첨부파일 다운로드는 회원그룹 '연구원' 이상 가능하오니, 경험치를 쌓아 진급한 후에 이용 부탁드립니다.
4) 무료 콘텐츠의 본문은 구매절차 없이 즉시 이용할 수 있으며, 판매 납포인트가 있는 콘텐츠는 구매 후 이용할 수 있습니다.
5) 콘텐츠 판매에 따른 납포인트 수익은 지정한 비율(50%)에 따라 판매자에게 지급하며, 납포인트 수익을 통해 진급을 빨리할 수 있습니다.
6) 구매 후 평가를 하면 구매 납포인트의 20%를 돌려 드립니다.
| 판매자 | 바다새 | 판매 납포인트 | 무료 | 평점 |  0점 / 총 0명 참여 |
|---|
안녕하세요?
회로도 작성후 PCB decal을 지정해주고 netlist 생성하였는데 다음과 같은 에러가 나옵니다.
Design to Library Part Consistency Check
----------------------------------------
Part Type LED has the following gate pins that do not match to the Library part:
(2 K) (1 A).
Non matching Part Type LED is used by the following parts:
D1.
Part Type CAP_NP not found in Library - not able to check following parts:
C5 C18 C4 C9 C7 C19 C6 C10 C3 C8
C1.
Part Type CAP_POL not found in Library - not able to check following parts:
C2.
Part Type R not found in Library - not able to check following parts:
R4 R5 R3 R6 R2 R1.
Part Type SFS5-5 not found in Library - not able to check following parts:
U1.
Part Type CONN_ASY_PCB_10_2 not found in Library - not able to check following parts:
J6.
Part Type CRYSTAL not found in Library - not able to check following parts:
X1.
Part Type CONN_PCB_3 not found in Library - not able to check following parts:
J1 J2.
Part Type SW_PB_SPST not found in Library - not able to check following parts:
SW1.
Part Type RELAY_SPDT_4 not found in Library - not able to check following parts:
RL1.
Part Type 7490_8 not found in Library - not able to check following parts:
J5 J10 J13 J12.
Part Type OPTO_ISOLATOR_0 not found in Library - not able to check following parts:
U2.
Part Type MAX232/SO_1 not found in Library - not able to check following parts:
U4.
Part Type 78XX/TO not found in Library - not able to check following parts:
U7.
Part Type ATMEGA128 not found in Library - not able to check following parts:
U3.
Part Type CONN_PCB_4 not found in Library - not able to check following parts:
J3.
Part Type DIODE has the following gate pins that do not match to the Library part:
(2 K) (1 A).
Non matching Part Type DIODE is used by the following parts:
D2.
Part Type R_2 not found in Library - not able to check following parts:
R20 R10 R19 R9 R15 R13 R14 R16 R11 R12
R17 R8 R18 R21.
Part Type TS12A4451 not found in Library - not able to check following parts:
U6.
Part Type CAPACITOR_NON-POL not found in Library - not able to check following parts:
C12 C16 C22 C14 C15 C13 C21 C11 C20.
Part Type RESISTOR_VAR not found in Library - not able to check following parts:
VR2 VR4 VR3 VR7 VR8 VR1 VR5 VR6.
Part Type 7490_3 not found in Library - not able to check following parts:
J14 J4.
Part Type DIODE_2 not found in Library - not able to check following parts:
D7 D6 D5 D4.
Part Type 7490_2 not found in Library - not able to check following parts:
J11.
Part Type LM324_0 not found in Library - not able to check following parts:
U9.
Single/Zero Pin Net Warnings
----------------------------
Net GND has less than two pins in PCB net list file.
Schematic Connectivity Errors
-----------------------------
Power or Ground Symbols used with wrong Net Name
+12V
PAGE1 X8200 Y8100 - Power Symbol used for net: +5V
PAGE2 X8000 Y8100 - Power Symbol used for net: +5V
PAGE2 X7600 Y5800 - Power Symbol used for net: +5V
PAGE2 X7600 Y3800 - Power Symbol used for net: +5V
PAGE2 X2100 Y3000 - Power Symbol used for net: +5V
왜 이런 에러가 나올까요?
- ECAD 아무거나 (172)
- PADS (352)
- Allego & OrCAD (149)
- EDA Simulation (23)